Page 1OPERATING INSTRUCTIONS AND ASSEMBLY MANUALBefore operating your new XTM Racing XST 4WD Truggy RTR, please read and understand the warnings liste
Page 10STEP 3: CHECKING THE STEERING AND THROTTLE/BRAKE CONTROLSq With both the transmitter and the receiver turned on, rotate the transmi
Page 11UPGRADE TIPTo prevent your XST 4WD Truggy RTR from going out of control should the radio control system encounter signal loss, we strongly sugg
Page 12Refer to the photo at left to familiarise yourself with your engine's carburettor. All of the carburettor settings come preset from the fa
Page 13q Using your glow plug wrench, verify that the glow plug and its washer are installed in the cylinder head and tight. If they're not alre
Page 14q Connect a fully charged glow starter to the top of the glow plug, making sure that the glow starter is locked rmly onto the top of the glo
Page 15The glow plug can make a big difference in how your engine performs. We recommend using a 'medium' or 'hot' heat-range glow
Page 16If, during the break-in process, the pull-starter slips when you try to start the engine, the one-way bearing and pull-starter
Page 17BASIC ENGINE MAINTENANCETo keep your engine operating at peak performance there are some basic maintenance procedures that need to be performed
Page 18The toe angle is the angle of both front tyres (or rear tyres) to each other, when viewed from above. Toe-in is when the front of both tyres po
Page 19With both the transmitter and the receiver turned on, and the throttle trim and the servo arm centred, the XST 4WD T
Page 2l Never use any fuel in your engine other than glow fuels specically designed for use in model car engines. Use of any other types o
Page 20Changing the shock oil (the oil inside the shocks) will change the damping characteristics of the shocks. Typically,
Page 21The XST 4WD Truggy RTR features front, centre and rear bevel gear differentials that each feature O-Ring seals and c
Page 22Rear squat can be adjusted using the rear suspension holder. Installing the rear suspension holder upside down causes t
Page 23MAINTAINING YOUR XST 4WD TRUGGY RTR Following a simple maintenance schedule will ensure that your XST 4WD Truggy RTR operates in top condition
Page 24TROUBLESHOOTING GUIDEThis troubleshooting guide has been provided to help you diagnose and solve most problems that you may encounter with your
Page 25IF YOU'RE HAVING A PROBLEM WITH THE CHASSISPROBLEM CAUSE SOLUTION1) XST 4WD Truggy RTR pulls A) Steering trim out of adjustment A)
Page 26(149895) Pin 4x26.6mm -- 6149895149895149895149895149895149895149895149895149895149895149895149563149899149893149891148570149905149897148602148
Page 27STEP 2: FRONT AND REAR DIFFERENTIAL HOUSINGS(148624) Shim 8x12x0.2mm -- 2(149563) Ball Bearing 8x16x5mm -- 4(148593) Round Head Tapping Screw 2
Page 28STEP 4: FRONT SHOCK TOWER(148558) Lock Nut 3mm -- 4(148576) Button Head Tapping Screw 3x10mm -- 1(148506) Cap Screw 3x16mm -- 4(148511) Cap Scr
Page 29STEP 6: FRONT UPPER SUSPENSION ARMS(149491) Turnbuckle 5x25mm -- 214978814949114978811.4mmSTEP 7: FRONT LOWER SUSPENSION ARMS AND CVD (148558)
Page 3The XST 4WD Truggy RTR is a purpose-built truck meant to handle the different terrain it encounters. With 4mm thick aluminium shock towers, thre
Page 30STEP 8: FRONT SUSPENSION(148558) Lock Nut 3mm -- 1(148584) Button Head Tapping Screw 4x12mm -- 2(148650) Cap Screw 3x42mm -- 2(149901) Hinge Pi
Page 31STEP 10: WING MOUNT(148612) Button Head Tapping Screw 3x18mm -- 4(149271) Post 6x32mm -- 2149271149271149271148612149271148612149271STEP 11: RE
Page 32STEP 12: REAR HUBS(148574) Grub Screw w/Threadlock 5x5mm -- 2(149261) Pin 2.5x16.8mm -- 2(148624) Shim 8x12x0.2mm -- 2(149563) Ball Bearing 8x1
Page 33STEP 15: REAR SUSPENSION(148560) Flanged Lock Nut 3mm -- 2(148584) Button Head Tapping Screw 4x12mm -- 2(149901) Hinge Pin 4x67.2mm -- 2(148508
Page 34STEP 17: FRONT CHASSIS BRACE(148559) Lock Nut 4mm -- 1(148634) Button Head Machine Screw 3x12mm -- 1(148651) Cap Screw 4x55mm -- 11485591492861
Page 35STEP 19: STEERING TIE-RODSSTEP 20: SERVO SAVER AND STEERING LINKAGES(148558) Lock Nut 3mm -- 4(148509) Cap Screw 3x20mm -- 2(149457) Servo Save
Page 36STEP 21: FRONT SUSPENSION MOUNTING AND STEERING LINKAGE(148558) Lock Nut 3mm -- 2(148554) Washer Head Machine Screw w/Threadlock 4x10mm -- 2(14
Page 37STEP 22: REAR SUSPENSION MOUNTING(148558) Lock Nut 3mm -- 1(148540) F/H Machine Screw 3x15mm -- 1(148598) F/H Tapping Screw 4x16mm -- 4Step 16S
Page 38STEP 23: RECEIVER BOX(149860) Flanged Lock Nut 4mm -- 1(148576) Button Head Tapping Screw 3x10mm -- 1214857614857614986014986014987114986014987
Page 39STEP 25: RADIO TRAY MOUNTING(148546) F/H Machine Screw w/Threadlock 3x8mm -- 3(148600) F/H Tapping Screw 3x10mm -- 4(148576) Button Head Tappin
Page 4RECOMMENDED TOOLS AND SUPPLIESThis section lists the recommended tools and supplies that you need to purchase and have onhand to nish assemblin
Page 40STEP 26: CENTRE DIFFERENTIAL(148566) Grub Screw w/Threadlock 3x3mm -- 2(148593) Round Head Tapping Screw 2x10mm -- 4(149284) Brake Pin 3x10mm -
Page 41STEP 27: CENTRE DIFFERENTIAL AND DRIVE SHAFTS(148607) F/H Tapping Screw 4x12mm -- 4149501Step 26148772148607Step 25
Page 42STEP 28: FUEL TANK(148546) F/H Machine Screw w/Threadlock 3x8mm -- 2(148550) Washer Head Machine Screw w/Threadlock 3x10mm -- 2(149287) Post 6x
Page 43STEP 29: ENGINE AND CLUTCH(148558) Lock Nut 3mm -- 4(148502) Button Head Machine Screw 3x6mm -- 1(148506) Cap Screw 3x16mm -- 4(149414) Shim 5x
Page 44STEP 31: AIR FILTER(148600) F/H Tapping Screw 3x10mm -- 1(149571)AirFilter Oil - Not Included149409149409149410Step 30149411149409149409148600A
Page 45STEP 33: ENGINE MOUNTING(148570) Grub Screw w/Threadlock 4x4mm -- 1(148514) Button Head Machine Screw w/Threadlock 5x10mm -- 4Step 321485701485
Page 46STEP 34: FUEL PICK-UP AND PRESSURE TUBINGFuel Pressure TubingFuel Pick-Up TubingSTEP 35: SHOCK BODIES AND SHOCK SHAFTS(149842) Lock Nut 2.6mm -
Page 47STEP 36: SHOCK OIL149850149847Silicone Shock Oil(Not Included)After lling with shock oil, GENTLY pump shaft up and down to eliminate air bubbl
Page 48STEP 38: FRONT SHOCK MOUNTING(148560) Flanged Lock Nut 3mm -- 2(148542) F/H Machine Screw 3x20mm -- 2STEP 39: REAR SHOCK MOUNTING(148560) Flang
Page 49STEP 40: STEERING LINKAGE(148558) Lock Nut 3mm -- 1(148560) Flanged Lock Nut 3mm -- 1(149333) Threaded Stud 3x16mm -- 1(148634) Button Head Mac
Page 5l 8-Pack 'AA' Alkaline Batteries for Transmitterl 4-Pack 'AA' Alkaline Batteries for Receiverl High-Quality After-Run Oil
Page 50STEP 42: THROTTLE AND BRAKE LINKAGE MOUNTING(148566) Grub Screw w/Threadlock 3x3mm -- 4Step 41Retaining ScrewIncluded with Servo148566148760149
Page 51STEP 44: ANTENNA SUPPORT TUBEReceiver BoxAntenna SupportTubeSlide the antenna through the antenna support tube, then push the antenna sup
Page 52STEP 46: WHEELS, BODY AND WING MOUNTING (149259) Wheel Nut 17mm -- 4149321149522149319149319148776149319149319Step 45149259Step 44149259Step 45
Page 53REPLACEMENT PARTS LISTWe stock a complete set of replacement parts for your XST 4WD Truggy RTR. Listed below are the replacement parts that are
Page 54149273Chassis Brace - Front149274Chassis Brace - Rear149281Centre Differential Mount149343Steering Knuckles (Pk2)149334Steering Rod Set - 5mm (
Page 55149408Clutch Shoes & Springs - 1mm (Pk3)149381Hub Studs - Rear (Pk4)L=43.5mm149377Hub Studs - Front (Pk4)L=37.5mm149363Shock Springs - 1.6m
Page 56149549Ball End - 4mm for 7mm Ball (Pk4)1497314mm Ball with Flange (Pk4)149781Suspension Arms - Lower Front (Pk2)149783Suspension Arms - Lower R
Page 57149911Gearbox Halves - Front or Rear149915Suspension Plate Holders149963CVD Universal Joint - Front (Pk2)L=168.7mm149926Engine Mount Spacers -
Page 58 148566 Grub Screws with Threadlock 3x3mm QTY. 5148570 Grub Screws with Threadlock 4x4mm QTY.
Page 59We stock many option parts for your XT2 Racer - Track Edition RTR. Listed below are the option parts that are available along with their respec
Page 6BECOMING FAMILIAR WITH YOUR XST 4WD TRUGGY RTR, CONTINUED...Air Filter: The air lter is made of foam and prevents dirt and debris from enterin
Page 60149580Clutch Bell - 14T (Single Speed)149581Clutch Bell - 15T (Single Speed)149582Clutch Bell - 16T (Single Speed)149583Clutch Bell - 17T (Sing
Page 61Option Part for 149825. Use with 149799149798Clutch Bell for 12T/17T Pinion GearsOption Part for 149825. Use with 149798149799Pinion Gear 12T/1
Page 62149407Clutch Nut Assembly - O.S.149546Fuel FilterGeneral Options145890Sure Start Electric Starting System146077Electronic FailsafeReplaces Engi
Page 63146700 Silicone Oil # 250 - 2.5oz 146701 Silicone Oil # 300 - 2.5oz 146702 Silicone Oil # 350 - 2.5oz 146703 Silicone Oil # 400 - 2.5oz (s
Page 64Before returning your XST 4WD Truggy RTR for warranty consideration, the status of the unit must be within the terms of the Warranty Informatio
Page 7TIPS FROM THE PROSYOUR XST 4WD TRUGGY RTR SHOULD INCLUDE THE FOLLOWING ITEMS SEPARATELY IN THE BOX:l Tyres and Wheels (Glued)l Body Clipsl De
Page 8q Push the transmitter antenna down into the moulded hole in the top of the transmitter.q Thread the antenna (clockwise) into place and tighte
Page 9q Slide the receiver antenna wire into one end of the antenna support tube and out the other end.q Push the end of the antenna support tube
Commentaires sur ces manuels